Elko eLAN-RF-003 Manual de instrucciones descargar pdf (Pagina 32)

60mm

21mm

<0.5s

<0.5s >0.5s >0.5s

<0.5s

<0.5s >0.5s

<0.5s

a b c

<0.5s

<0.5s >0.5s >0.5s

<0.5s

<0.5s >0.5s

<0.5s

a b c

t=3s

<0.5s

<0.5s >0.5s >0.5s

<0.5s

<0.5s >0.5s

<0.5s

a b c

t=3s

<0.5s <0.5s

<0.5s >0.5s

<0.5s

<0.5s >0.5s

<0.5s

<3s

<3s >3s <3s >3s

<3s

a b c

RFDA-11B RFDA-71B

RFDA-11B

RFDA-71B

R L C

RFDA-11B

RFDA-71B

R L C

RFDA-11B

RFDA-71B

R L C

Function 1 - press 1x Function 2 - press 2x

Function 3 - press 3x Function 4 - press 4x

Sunrise - press 5x Sunset - press 6x ON/OFF - press 7x

a) Press the button for less than 0.5 seconds to switch on the light;

press again to switch it o .

b) Press and hold the button for more than 0.5 seconds to adjust

brightness continuously. After releasing the button, the brightness

level is saved into memory and pressing the button shortly later

will switch on/o the light to this intensity.

c) Brightness may be adjusted at any time by pressing and holding

the button. The receiver remembers the adjusted value even after

disconnecting from power supply.

If the light is o , press the button to

switch it on. If the light is on, press the

button to switch it o .

After pressing the button, the light will

start to switch on during the selected

time period, ranging from 2 seconds to

30 minutes.

After pressing the button, the light will

start to switch o during the selected

time period, ranging from 2 seconds to

30 minutes.

a) Press the button for less than 0.5 seconds to continuously switch on

the light for 3 seconds (at 100% brightness). By pressing the button

shortly again, the light will continuously switch o for 3 seconds.

b) Press and hold the button for more than 0.5 seconds to adjust

brightness continuously. After releasing the button, the brightness

level is saved in the memory and pressing the button shortly later

will switch on/o the light to this intensity.

c) Brightness may be adjusted at any time by pressing and holding

the button. The receiver remembers the adjusted value even after

disconnecting from power supply.

a) Press the button for less than 3 seconds to switch on the light; press

again to switch it o .

b) To avoid undesirable brightness adjustment, the continuous

brightness regulation is only activated pressing and holding the

button for more than 3 seconds. After releasing the button, the

brightness level is saved in the memory and pressing the button

shortly later will switch on/o the light to this intensity.

c) Brightness may be adjusted by pressing and holding the button

for more than 3 seconds at any time. The receiver remembers the

adjusted value even after disconnecting from power supply.

a) Press the button for less than 0.5 second to switch on the light,.

By pressing the button shortly again, the light will continuously

switch o for 3 seconds (at 100% brightness).

b) Press and hold the button for more than 0.5 second to adjust

brightness continuously. After releasing the button, the brightness

level is saved into memory and pressing the button shortly later

will switch on/o the light to this intensity.

c) Brightness may be adjusted at any time by pressing and holding

the button. The receiver remembers the adjusted value even after

disconnecting from power supply.

t=2s..30min t=2s..30min

serves for light dimming and creating light scenes (4 preset light scenes)

allows dimming bulbs and halogen lights with electronic or wound R, L, C 250VA transformer

RFDA-11B: single-function - button dimmer

RFDA-71B: multifunction - 6 light functions, ON/OFF function, possibility to set continuous switching on/o of

light (between 2 seconds and 30 minutes)

easy control: switch on/o the light by pressing the button shortly; adjust brightness by pressing and holding

each actuator can be controlled by up to 32 channels (1 channel is represented by 1 button on the wireless wall

switch button, keychain or the RF Touch-W / B unit)

electronic overcurrent protection - the output is switched o in case of overloading or short-circuit

for programming and manual control, press the Prog button

installation box design (such as KU-68)

Supply voltage:

Apparent input:

Dissipated power:

Supply voltage tolerance:

Connection:

Output

Resistance load:

Capacity load:

Inductive load:

Control:

RF, by command from transmitter:

Manual control:

Range in free space:

Other data:

Operating temperature:

Operating position:

Mounting:

Protection:

Overvoltage category:

Contamination degree:

Terminals (CY wire, cross-section):

Length of terminals:

Dimensions:

Weight:

Related standards:

Technical parameters

230 V AC / 50 Hz

8.3 VA / cos φ = 0.1

0.83 W

+10/ -15 %

3 conductors, including neutral

250 VA*

868 MHz

PROG (ON/OFF)

up to 160 m

-15 to + 50 °C

any*

free at lead-in wires

IP 30

III.

3x0.75 mm

90 mm

49 x 49 x 21 mm

40 g

EN 60669, EN 300 220, EN 301 489

Directives RTTE,Gov. Reg. No..426/2000Sb(Directives 1999/EC))

Wiring with diﬀ erent types of loadDevice description

CONTROLS

EAN code

RFDA-11B: 8595188136846 / RFDA-71B: 8595188143080

Device status indicator

Output to appliance

Program button (ON/OFF

manual control)

Neutral conductor

Phase conductor

R-Resistance L-Induction C-Capacity

RF receiver: Dimming actuator RFDA-11B, RFSA-71B

* For more information, see p. 48

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 51 52

Comentarios a estos manuales

Sin comentarios

Elko eLAN-RF-003 Manual de instrucciones Pagina 32

Comentarios a estos manuales